X-GRIP Frame Protector

Fits:HONDA CRF 250 L-M 13, HONDA CRF 250 L-M 13-20, HONDA CRF 250 L-M 14, HONDA CRF 250 L-M 15, HONDA CRF 250 L-M 16

Japanese Webike user

Very Good

Jan 15, 2022

One point Fashion

I bought this because the paint on the Frame had faded on OffBoots.

It looks Up with a splash of color.

Helpful?

I wanted to put it on md47, but it didn't work at all.

Fits:HONDA CRF 250 L-M 13, HONDA CRF 250 L-M 13-20, HONDA CRF 250 L-M 14, HONDA CRF 250 L-M 15, HONDA CRF 250 L-M 16

Japanese Webike user

Average

Dec 22, 2021

Sometimes you just can't help it, can you?

I wanted to put it on md47, but it didn't work at ...

Helpful?

crf250rally ACERBIS X-GRIP FRAME PROTECTOR

Fits:HONDA CRF 250 L-M 13, HONDA CRF 250 L-M 13-20, HONDA CRF 250 L-M 14, HONDA CRF 250 L-M 15, HONDA CRF 250 L-M 16

Typhoon

Excellent

Feb 20, 2021

제 2020년식 crf250rally엔 왼쪽 부분 프레임에 호스 고정 브라켓이 있어약간 어긋나지만, 힘으로 누르면잘 맞습니다그냥 플라스틱 재질이며 케이블 타이로 고정하는데, 케이블 타이 빼는게 생각보다 어려웠네요 ㅋㅋMy 2020 crf250 rally has a rubber pipe fixing bracket on the left side frame, so it doesn't fit well, but it fits well when pressed with force.It is made of plastic and is mounted with a cable tie.

Helpful?

Fits:HONDA CRF 250 L-M 13, HONDA CRF 250 L-M 13-20, HONDA CRF 250 L-M 14, HONDA CRF 250 L-M 15, HONDA CRF 250 L-M 16

Japanese Webike user

Excellent

Jul 10, 2020

These are good Items!

Just putting this on will give you an overall tighter look.
The color scheme is also good without being stigmatized by the OEM exterior.

M5 Hexagonal Wrench and radio pliers for mounting (Nipper) was needed and the work took 10 minutes.
The Left Side has three in-Hemp palmocks, the Right Side has two screws and Install with three in-hemp palmacks.
It is mentioned in another review that one of the Right Side locations cannot be installed, but the Rear It can be attached to the Master Cylinder of the brake.

Helpful?

Fits:HONDA CRF 250 L-M 13, HONDA CRF 250 L-M 13-20, HONDA CRF 250 L-M 14, HONDA CRF 250 L-M 15, HONDA CRF 250 L-M 16

Japan User(translated)

Very Good

May 21, 2020

Parenthesis OK

2019 MODELCRF250L

I bought it because I was concerned about the slippage in the Frame when I wore Boots
I chose this one because it looks better and cheaper than ZETA's Aluminum
Black plastic with red hard rubber inserts
The LeftParts were warped, so I used a heat gun to mold them, but even if I didn't, Tie It's not a problem because it's held down by the Wrap

Left is Tie Wrap Fixing only
The Right reuses the two Screws in the Frame where OEMGuard is stopped It also uses Tie Wrap as well as Left
The other reviewers say that they use Sub-frame's Screw, but the Screw is very easy to touch No It is said that Tie Wrap doesn't stop at 1 pc, but it is also said that Master Cylinder and If you can pass through the gap between the frames, the frame is durable enough
There is a hole in the Screw where the load is applied, so you won't have to touch it
Instruction Manual is a translation (please do not enter here, but ScrewQuantity on the Right:I have to decide where to cut the 2pc and Tie Wrap, so Instruction It takes about 5 minutes without looking at the Manual

Looks pretty parenthesis better
Large Satisfied!