Left Lever For Honda

Fits:HONDA AX-1 AX-1 1987-1989, HONDA Bol D'or 81 FBB Bol D'or 81 FBB, HONDA Bros 400 Bros 400 1988-1990, HONDA CB125T CB125T 1987-2000, HONDA CB125T CB125T 1987-2000 T J

Japanese Webike user

Excellent

Aug 17, 2021

Clutch is now lighter.

When I installed it, the grip of the clutch became surprisingly light because I cleaned and applied grease. It looks great with WhiteTank and Contrast in Black. The installation took a little more time than the brake lever. The photo is not Clutch but Brake lever. (NC31) It is

Helpful?

Fits:HONDA AX-1 AX-1 1987-1989, HONDA Bol D'or 81 FBB Bol D'or 81 FBB, HONDA Bros 400 Bros 400 1988-1990, HONDA CB125T CB125T 1987-2000, HONDA CB125T CB125T 1987-2000 T J

Excellent

May 19, 2019

That's a lot easier

I replaced the Clutch lever and Brake lever at the same time
Because the OEM Product Lever was only a little far away, Lever operation Grip I had to regrip the Lever with my fingers, or I had to regrip the Lever with my fingers, so I thought it was a good idea to improve and replace it You were right You were right It's much easier And the part where the clutch switch hits (Because it's sharp?) Because there was an imprecation that it would break, the part was beaten a little and made round There is no problem at present, because Engine is applied to each GEAR other than Neutral I'm relieved

Helpful?

Fits:HONDA AX-1 AX-1 1987-1989, HONDA Bol D'or 81 FBB Bol D'or 81 FBB, HONDA Bros 400 Bros 400 1988-1990, HONDA CB125T CB125T 1987-2000, HONDA CB125T CB125T 1987-2000 T J

Excellent

Dec 26, 2017

Cost Poor performance

I used this for CB 750 RC 42, Lever liked Black. It used to be a Korea made BlackLever, but I like it because it is glossy here. It is Exactly to RC 42 and there is no astringentness The operation feeling is very good

Helpful?

Fits:HONDA AX-1 AX-1 1987-1989, HONDA Bol D'or 81 FBB Bol D'or 81 FBB, HONDA Bros 400 Bros 400 1988-1990, HONDA CB125T CB125T 1987-2000, HONDA CB125T CB125T 1987-2000 T J

Very Good

Nov 29, 2017

It is easy to use

Even when it is exchanged from OEM, there is almost no sense of incongruity in use and design.
Moreover, since the fingertip grips firmly, it does not slip and fingers slip off almost.
Because the Lever holder is Black, I got a feeling of cohesiveness and made it Black and it was the correct answer.

Helpful?

Fits:HONDA AX-1 AX-1 1987-1989, HONDA Bol D'or 81 FBB Bol D'or 81 FBB, HONDA Bros 400 Bros 400 1988-1990, HONDA CB125T CB125T 1987-2000, HONDA CB125T CB125T 1987-2000 T J

Poor

Nov 11, 2015

operation

I exchanged because Clutch was hard. As a result, it is somewhat lighter, but Handlebar and Lever are just good. A little Custom feeling came out. It is a pity that the tip is round, but looking will change if you cut it flat.