Off-Road Series Taillight

The product concerned that Valve size was confirmed the other day was converted to LED immediately.
Because of the shape of the lens and the position of the bulb socket, the size of the LED bulb that can be used must be almost the same as the original G18 bulb.

This is a re-evaluation because each Clearance was too strict and I had some doubts about the Universality.

I don't know if this will be helpful, but I'll upload the photo of the LED Bulb I could use.

I bought this to put on my XLR80R Tail. I disassembled it as soon as it arrived because I had seen in other impressions that the Valve could not be replaced.

The Lens is only stopped by PlusScrew on the four sides of the back, so the Lens came off easily.
Inside, to be parallel to the iron plate of Base, Socket for BAY15D mouth Gold is installed. To be sure, when Valve is removed, the imprint of 12v23/8w is confirmed. At least, Valve is attached directly to Light body, because it was able to confirm that it is not the situation which says that it is impossible to exchange, it is a relief.

When I disassemble it, I noticed that the Clearance of Valve and Base steel plate is Zero as far as I can see.
The Valve that was installed on the product was G18Size, but it was in contact condition, so when you change to LED, you need to pay attention to the size of the LED Bulb or replace each Socket.
Also, there is no license plate lamp, so you need to prepare it separately.

It is a Small Type from OEM, and the Design is not too old and not too new, just right for a 34 years old car.
In addition, the type of Wiring color is described in the Instruction Manual included in the package, and the installation was nothing but replacing the OEM Product, so there was nothing to worry about.

XLR 125R 's tail surroundings were bad, so I wanted to make it a little better now I was looking for a Tail lamp.
Form a little earlier off car etc etc etc etc. And the price is also about 3,000 yen, Manufacturer also purchased it by saying KIJIMA.

Although it is not possible or impossible to build it, I do not know whether it is possible to issue the Wiring of License Plate Light, but there are two cutouts at the bottom of the Rubber around the Tail lamp.
Thanks to you I was able to trace Wiring of License Plate Light cleanly.

Since installation can be carried out firmly with two Bolt, there is not worry of dropout.
Since Wiring also has a Bullet terminal terminal attached from the beginning, it can be installed easily.
I wanted to share Wiring of License Plate Light, so I cut it and tried it again ,,,.

I think that there is nothing to pay particular attention to, other than having to prepare License Plate Light separately.
Although it is not disassembled, it is assembled with Screw, so it seems that exchange is possible even if the light bulb is burned out.

I bought it for Replacement of SUPER SHERPA's wasteful Large Tail lamp. It is a product of Universal, so some processing is necessary, but it will be Rear Fender which was refreshing for the first time in Small. It is a good product that we have built well. Since there is no License Plate Light, it also needs to be processed.

I replaced Kawasaki SUPER SHERPA's Tail lamp with this Lamp. Rearreshing around Rear makes it feel good. However, the protrusion of the installation Bolt was too long, and it was hard to cut.
Wiringetc. I had prepared a service manual, but I could easily do it just by reading the contents in the attached Instruction Manual. However, since there is no function of License Plate Light, we installed the LED License Plate Lamp of AsianMotors at the same time. Although there was a structure which can not exchange Lamp with other people's review, was it a lot difference that I bought? Lamp exchange was possible because Lens can be removed if 4 Screws are relaxed. I will try to replace it with an LED bulb in the meantime. ☆ If it was a bit cheaper ☆ 5.