Brake Pad RX3 [Standard Type/Street, Race]

Fits:KAWASAKI ER400 ER-4n ER400 ER-4n 11-Up Position: Rear, Quantity required: 1, KAWASAKI ER400 ER-4n ABS ER400 ER-4n ABS 11-Up Position: Rear, Quantity required: 1, KAWASAKI ER650 ABS ER650 ABS 06-Up Position: Rear

flexible (e.g. in terms of impact)

Very Good

Jun 8, 2019

When I did the overhaul of the rear brake area, I also changed the pad I changed the OEM pad as it was not changed for 22,000km since I bought a new car, but the OEM pad was not used at all I didn't Basically, I don't know much of a difference between fee rings because I don't use rear brakes much The state before the replacement of MASTEROH & CaliperOH & Fluid It's impossible to make a character imprint because it's different from But, well, as far as Feel is concerned, it's an extension of the OEM It's not overly effective or completely ineffective, it's just a matter of putting Front and Rear together in the same brand This was an OK choice because I just wanted to have it all in Pad, probably, but in terms of efficacy I think it's pretty easy to use for speed fine tuning while cornering

Helpful?

I used it for MOTO GUZZI.

Fits:APRILIA Moto 6.5 650 95 Moto 6.5 650 95 Position: Front, Quantity required: 1, APRILIA MX 125 MX 125 04- Position: Front, Quantity required: 1, APRILIA RST 1000 Futura RST 1000 Futura 01- Position: Rear

Japanese Webike user

Excellent

Feb 16, 2021

2020 by Corona
I bought it because the Shop told me that the part would not come in and I would have to replace it myself.
As for the Exchange Kill.
It was easy, but it's an important safety part and you are responsible for it.
If you're not sure, Shop is a good place to start.

Now, the impression that I used this Pad.
(This is assuming that you are only using the bike for touring.

It stops securely with no problems.
Touchetc. is not a problem either.
I don't know about durability yet.
Therefore, it is unrated.

It's not bad.

Helpful?

Fits:APRILIA ETV 1000 Caponord 2001-2004 Position: Rear, Quantity required: 1, APRILIA ETV 1000 Caponord 01-04 Location:Rear:1, APRILIA RSV 1000 Factory Pista 04- Part Number:Rear Necessary Number:1, APRILIA RSV 1000 Factory Pista 2004-Up Position: Rear

Not available for OEM Caliper

Excellent

Apr 28, 2019

RSV4 OEM Caliper has a heat shield in the piston, so the thickness of the RX3 is not as thick as that of the RX3 I'm not going in
After Brembo crab is no problem
I replaced the Caliper for installation
The in-play stars were my impressions of the VTR1000F when it was on
You must check the inner diameter of the Piston for heat shielding before you install it

Helpful?

Fits:APRILIA 750 Shiver 750 Shiver 06- Position: Rear, Quantity required: 1, APRILIA Caponord 1200 Caponord 1200 13- Position: Rear, Quantity required: 1, APRILIA Caponord 1200 Rally Caponord 1200 Rally 13- Position: Rear

Excellent

Dec 16, 2018

Not bad

2017 BMW S1000RR. installation is perfectly fine. not gone to Circuit However, the braking power on the Pass Level is comparable to that of the OEMs, especially in terms of Dust I didn't find any defects, and the look of the Caliper gap isn't too bad (a little (Orange is back) I couldn't give it a Life rating because I just put it on, so I gave it 3 stars for now

Helpful?

It is the second purchase this time It is satisfactory performance, but a little more durability

Average

Dec 9, 2018

OEM Product wore out and had to be replaced by another motorcycle before The Manufacturer that I used to work with was a reliable one, so I thought this Manufacturer products