Caliper Support

Fits:KAWASAKI GPZ900R NINJA GPZ900R NINJA 90-98 A7-A11, KAWASAKI ZEPHYR1100 ZEPHYR1100 92-06 Not for RS, KAWASAKI ZX-9R ZX-9R Europe (-95) / US (-96), KAWASAKI ZXR400 ZXR400 89-99, KAWASAKI ZXR400R ZXR400R 89-99

Very Good

May 3, 2021

In Φ300

[How is it used?
Used in the OEMRotor300 era.
Silver, Compact and thick.
I didn't feel rigid anxiety.
Although the hole dimensions are provided, installation should be done with the Caliper on the side that it is going to move against the Fork outer during breaking and then bolt it in place.
Otherwise, the frictional force caused by the bolt tightening alone may cause the risk of gapping.

Was the one you received as per Image?
Yes

Was the installation difficult?
It's easy if you know the hang and the concept.

How was your experience with it?
OK

[Included Parts:were they on?
Yes, I was wondering if Shim was there.

[Was there anything that disappointed you?
None

Helpful?

Perfect, and just what I wanted

Fits:YAMAHA RZ350 RZ350 81-82, YAMAHA XJ400 XJ400 80-82, YAMAHA XJ400D XJ400D 80-82, YAMAHA XJ400Z XJ400Z 80-82, YAMAHA XJ400ZE XJ400ZE 80-82

NO NAME

Excellent

Jul 3, 2022

The caliper supports arrived very quickly all the way from Japan and the parts are of very high quality and fit perfectly. I will be fitting them to my UK 1980 Yamaha RD350LC (4L0) (also known as RZ350 in other countries) and I am very pleased with them. When I have fitted them I will attach another photo to this review.

Helpful?

Fits:YAMAHA RZ350 RZ350 81-82, YAMAHA XJ400 XJ400 80-82, YAMAHA XJ400D XJ400D 80-82, YAMAHA XJ400Z XJ400Z 80-82, YAMAHA XJ400ZE XJ400ZE 80-82

Excellent

Nov 9, 2021

Relief

I bought this because I went with brembo.
Of course, Exactly is attached, but you need to adjust the Shim to get Center.

Helpful?

Fits:HONDA CBR250R CBR250R 2011-2017 MC41 *Cannot be installed on 2010-2016 ABS models, HONDA RS125R RS125R 1990-1994 Nissin 2POT models

It's a bit forced. Crying 。

Average

Oct 4, 2021

This is a must have part for brembo installation.

I was not sure if it was Radial Mount or Axial Mount, but Axial is enough because it is OverQuality.

To install, just mount it on the Front fork and assemble the Caliper.

However, Aluminum Cut-out is not the same as "It's just the way it is. The feeling is ……

I think GCraft's Black Anodized Aluminum was more natural. (Sweat) 。

Helpful?

Fits:HONDA CBR250R CBR250R 2011-2017 MC41 *Cannot be installed on 2010-2016 ABS models, HONDA RS125R RS125R 1990-1994 Nissin 2POT models

I think it's fine, but at your own risk.

Excellent

Jul 31, 2021

I used it in the field where I put brembo4POD on VT250 SPADA.
The one I received is the one with no problems.
The BoltQuantity is included with the Caliper.:There are 2pc.
Be sure to check the fastenedTorque properly.

I think the Pad on the inside diameter side of the disc is slightly sticking out.
I tried to put it as far out as I could, but it was still too far. (;^ω^) It's like
What does it look like in RS?

Didn't seem to be a problem on the test drive.
It may be that it is still a self-responsibility as long as the conformity is not indicated by Manufacturer.

I don't think you'll have to spend a lot of money on Ok.