Looks like you access from European region.
Would you shop at webike.eu.com?
63.98 USD (10,200 JPY)
Delivery Information
In Stock, Ships within 48 hours.
Estimated arrival date around
Manufacturer's Part Number: ZE56-8619
Stock comparison length
WR250R '08-'17(-25mm)
WR250X '08-'17(±0mm)
Included tips (standard tips): 1Length: 55mm
Part Number: F4148 (Manufacturer's Part Number: ZE56-8919)
Special side stand extender is available.G4788(Manufacturer's Part Number: )ZE56-6990)
**Be sure to apply thread-locking agent to the tip mounting bolts when assembling tips.(Threadlocker not included)
*If there is a concern that the tip may rotate, apply a glue to the joint between the shaft and the tip as well.
*Adhesion to the joints should be done as necessary, since it will be difficult to replace the chips afterwards.
*The image may contain other products.
.
* The image is only for reference. The image shown may differ from the actual product.
Mainly lineup of short type for lowered vehicles, which is 25mm shorter than stock. *1
The height of the vehicle is set to avoid the instability of the vehicle body due to the change of the vehicle height, and to allow the vehicle to be used on rough roads with ease.
The removable tip can be replaced with an optional tip to adjust the height for standard and high lift vehicles. *2
Adopted forged A2014 to ensure strength and durability
*1 Some vehicles are available for high-lift vehicles and standard vehicles.
*2 Tilt depends on vehicle height.If the tip lengths do not match, please refer to the optional tip conversion table in the image and replace the tip.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
Reviews with image
Fits:YAMAHA WR250R 08-17, YAMAHA WR250X 08-17
Mar 31, 2022
I am using XWheel to make MOTARD, but the OEM length of X is a little too long for my vehicle, so I have replaced it with a +15mm tip.
It's not that much lighter than OEM, but it looks better, so it's a good part.
Fits:YAMAHA WR250R 08-17, YAMAHA WR250X 08-17
Oct 6, 2021
The ground contact part of the STAND can be rotated and fixed, so you can set the best STAND ground contact position according to your motorcycle's parking position. I'm happy with the way it looks.
View DetailFits:YAMAHA WR250R 08-17, YAMAHA WR250X 08-17
Jan 5, 2021
If you are looking for a lighter, non-rusting adjustable side stand then this is it. It looks good too which is possibly one of the real factors I've taken into account for the purchase. It also accepts the OEM spring so installation is just as easy as removing the stock.+Good looking+Lighter than stock by a bit+Doesn't rust+Easy to install+Adjustable-Expensive I think-No rubber footing prone to scratches
View Detail
Fits:YAMAHA WR250R 08-17, YAMAHA WR250X 08-17
May 20, 2020
It's short, so I adjusted the ride height
Installed on WR250R
Lower the lower part of the rear shock and adjust the spring position At -25mm, it tilts quite a bit at -25mm, both front and back are DRCSpringSoft..
Apparently, replacing it with Zita's Lowdown Link would be just the thing?
However, when LINK was exchanged, Rear became quite soft, and LINK was exchanged for a while has a history of reverting to OEM
The spring position of the rear spring is adjusted further and Fork is protruded by 20mm became
The texture is great, and if possible, a 5mm collar would be included so I could make some minor adjustments It's a Gold amount product in its own right and I hope you will consider it
It's a mating game, so it's only necessary to make each color of FemaleMale, so next time you can make a new one I'm thinking of producing it
Fits:YAMAHA WR250R 08-17, YAMAHA WR250X 08-17
May 1, 2019
Great looking - works excellent
Really a nice addition. As soon as I saw this product I was excited and hoped it performed as good as it looked. It does. The fit was very good, it works smooth and uses the stock bolt, sidestand switch and spring.
View Detail
Review detail
